Appliance Contact Paper

We have a black dishwasher , and the othe appliances are stainless, the story of a lot of people , I just installed , It looks great , like new. it is easy to installed , with patience, and the right tools . I used a squeegee. ; And do it in two sections , because my diswasher has a hole at he top for a hand to open .(Bosch) I waste a little for the top , until I make a template. We are very happy with the result . the adhesive is strong it took me an hour . But take in consideration that I have everything on hand. I don't know how long it will stay on . But now I ma very satisfied with the result .

I debated between a panel that had to be cut to size or this type of cover. I'm really glad I chose this. I read a lot of reviews and this one had more good than bad. I used it on our dishwasher (see pic). First I cleaned it really well. Then I measured and gave myself and extra inch (length). I took someones advice and had a squeegee ready, but didn't need it. I used a micro fiber cloth to smooth it instead. I had no problems with air bubbles or wrinkles. I went slowly and it worked just fine. I put strips on the sides also. One piece of advice if you do the sides... have the front piece overlap a little on the sides so when you do the sides it covers better.

For what this is it is great. I’m sure there are other products that look more like stainless but this did the job for me. $22 and I had the felt covered squeegee for install. If you can get your self one as it helped get rid of the air bubbles. Cutting was interesting but I took my time. The exacto knife would really grab as it is not like normal vinyl. Not really stretchy. I didn’t use heat as I was just trying to upgrade the look of my dish washer with out spending the money on a new stainless steel model. Texture is good. But like the title says it does look more chrome when you first see it rolled up. Once I applied it did have more of a stainless look. I first installed and the lines were vertical. I removed and replaced and used the line horizontal and to me I think it looks better.

I just bought my first home and after spending a bit to replace several other appliances, I decided the dishwasher could wait. I figured I’d at least try to update the dishwasher to match everything else and gave this a whirl after seeing some diy videos. I first tried working from top to bottom (wrong move) and it creased pretty badly. Usually you can work it the bubbles but this stuff IS STICKY. The more I tried to work the bubbles out the more it creased. I scrapped after about 4” and started over but this time started from a corner and worked outward little sections at a time. Then it worked like a dream. It is a little shinier than the other appliances but because they aren’t right next to each other you can’t really tell. Not to shabby and my friends are impressed!

The entire roll had defects that would not come out when the paper was applied. The marks seemed like they did not have adhesive on them and I could not get them to lay flat on the surface that I was covering. I applied this paper to the front of my dishwasher, so it is a very flat surface that I put it on, and of course I cleaned the surface before applying. I like the thickness and quality of the 'paper', except for the defects of course. I was past the return date before I used it and found the problem, so I am unable to return it. I have sent the supplier a message in hopes that they may send me a replacemen roll.

I purchased this stainless steel contact paper to update my appliances and countertops without the high cost of real stainless steel. The adhesive is strong and it was easy to apply. The silver brush finish gives a sleek and modern look to my kitchen. It's also waterproof and easy to clean. Overall, I am very satisfied with this product.

First off you have to be a magician to lay this down smooth with no bubbles. And then you have to perform a miracle to get the bubbles out. I used a flexible but firm plastic window film applicator to smooth out the bubbles. Good luck with that. The bubbles remain and the film gets all scratched. Then I decided to try it with a cotton towel wrapped around it. It still scratched the film. I started over on the back side of the panel I was installing on and made sure to be extra careful and roll the film tightly in the the panel as I rolled off the liner. Still tons of bubbles that you can't squeegee out. And of course the scratching of the film as you try to get the bubbles out. This was a waste of money and time. I bought a $9 can of Rust-Oleum metallic aluminum oil paint and it came out way better. I really wish I could get a refund but I used most of the roll trying to get it to work. Oh and the people that say you can pull it up and reposition, sure but you kink and stretch the film. This product needs to be thicker. Cheap junk

Saw the idea on pinterest about "upgrading" your old ugly appliances with contact paper. It was easy to pop out the decorative appliance panel without any tools. It would be frustrating to apply the contact paper to the appliance without removing the panel, but still doable. I removed each decorative panel, cleaned it off with a bleach wipe and let it air dry. I lined up the corner of the contact paper with a corner of the panel and used a credit card to wipe towards the roll to keep air bubbles from forming. The contact paper is thicker than typical paper and it was easy to keep bubbles from forming. Note: Another reviewer commented that it needs to be rolled from top to bottom, rather than left to right for wider appliances. I agree. This roll is slightly wider than my dishwasher panel so I was able to roll from top to bottom and the stainless steel pattern looks like the real thing. I could not be more pleased with the results! I highly recommend this particular item for a quick "upgrade" to old ugly appliances.

Buen material, diseño , me encantó, solo espero al técnico que me lo indtsle

Vraiment tres satisfaite, j’ai un lave vaisselle que je n’utilise jamais, il est blanc et quand j’ai changé mes electro pour des stainless j’ai gardé le meme lave vaisselle et c’est vraiment dépareillé. J’ai mis cette pellicule et je suis ravi du resultat. Facile d’installation

Like any tacky type film, it's not so easy to install. Once you do and you do it correctly, it really works well. It's hanging/sticking without a problem and I'm sure the dishwasher front can get warm. I put this on to an old dishwasher as it still works really well. Updated the look 100% The width is important so you can cover without trying to make a seam. I highly recommend this.

I used it on drawer fronts in the kitchen to match the appliances and it turned out well. Just be very careful of creases.

Pellicule trop mince, laisse paraître chaque petite imperfection dessous, trop luisante comparé à un vrai fini stainless