Rust Converter and Primer 1 Litre

Used on a car restoration to convert some rust which didn't require cutting out.previously I had used some hammerite Kurust so did a side by side comparison test. I coated the rusty box section with Kurust and at the side used aquasteel I then left to cure they both turned black and the Kurust appeared strongerI then applied salt water to the pair of samples and allowed to dry once dry I reapplied more salt water and left them in the sun, later that night the rain came down and the following morning I checked on the samples.The aquasteel was still as it was left with no signs of rust reappearing or breaking through, the Kurust however was starting to breakout in rust again.a couple of notes the test was extreme the salt water was very salty and left in the exposed sun and rain and both products are meant to be painted over and that would make a difference in itself.saying that the aquasteel was as it was when it was applied and was a winner for me its the one I will be using in the future.The samples are still in the open and I'll be watching them over the coming months and winter to see what happens and will update here

I've used this for a couple of winters keeping the rust at bay on a transit van and thought I'd share my experiences. This stuff is great and works really well if used correctly. The main point I can't stress enough is use it in warm, dry weather. Although the tech data sheet says min 6 deg C, the finish in cold, damp conditions is thin, brittle and 'pre-cracked': that is, it forms a sort of crazing which is perfect for moisure to get into and start levering little bits off again, so it won't last long. Similarly in damp conditions the chemical reaction seems a bit half-hearted and it never really cures properly. When the weather's warm and dry, the finish is more like a tough cured black resin, particularly when you've sploshed on a couple of coats. Second, depending on how thick the rust was to start with it may still be there underneath - deactivated but biding its time and waiting for a weakness! Like all coatings, the moment a stone chip exposes the rust to air/moisture again, even just a pinprick- it will get going again. Therefore the product is best regarded as a primer, think about what's going on top to prevent damage to the hard surface whether it's paint or waxoyl etc. Third, just to reiterate the instructions on the bottle - get all the flaky stuff off first. The stuff is good but it can't turn rust back to metal. If that means jabbing with a screwdriver with increasing concern as a tiny hole expands into a major welding job - well it was going to happen anyway! One of the pleasures of old car ownership in the UK. Finally I found that doing a reasonable job on all the rusty bits on the van used about 1 litre bottle. Hope this helps someone.

Superb product, does exactly what is says on the .... bottle :)Just brush it on and leave for twenty four hours, job done. You can paint or prime after and it holds back the rust for a long time. I painted a gate many years ago with this gear and it still looks great to this day! There are a few tiny pits of rust forming now but considering that it has weathered the storm for years, I am truly amazed at what this product does. Just make sure that all the flakey rust/paint is gone before application. I used a 1" brush and cover the areas I needed and then washed it in warn soapy water immediately after - this is very important otherwise you will end up with a soiled brush! If you have sensitive skin wear gloves and goggles if you are painting upside down, it goes without saying that you can replace a set of goggles but NOT your eyes!

Good stuff

Used this to protect some old weight plates in the garage from rusting during damp weather. It turns the rust black/blue and leaves an additional translucent protective layer on top. It has made the old iron plates appear rejuvenated. Friction may remove the outer protective/sealing layer over time but having witnessed the conversion of the rust underneath I think it has already done everything I wanted it to do. It goes a long way, I bought one litre and that's going to last for years. It saves a massive amount of time and effort compared to removing every trace of rust and priming and painting new (it can be effectively used as a primer layer apparently). Fantastic product!

Having tried a few of the well known brands without a lot of success on my Jaguar XKR, Aquasteel, maybe not the cheapest on the market, but the results after application provided an extremely hard coating, and sealed perfectly, just remove the loose rust first and leaving a covering of surface rust proved to work faultlessly. Unlike some products, this doesn’t scratch off easily. Overall delighted with the product, plus the prompt answers to my questions to their technical department. Will be buying again without hesitation.

Very effective. Works fast and turns the rust jet black. Easy to use and does exactly what it says it should. Recommended.

Bought this as a 1 litre bottle instead of the usual small branded bottles at my local car parts/accessory shops. This product seems more 'heavy duty' in my opinion, though I can't remember how thick the branded ones used to be, but this aquasteel seems very meaty stuff indeed. Have done some rust on the car and it turns it nice and black ready for a coat of paint. Water based as are the ones I used to use, so brushes clean easily in water. Very satisfied with it.