Black&blue PET braided sleeving

The 100ft braided PET expandable wire loom is a game-changer for organizing my cables! 🌟 With a 3/8 inch diameter, it provides the perfect fit for various wire sizes, helping to keep my workspace tidy and free from clutter. The braided design is not only durable but also flexible, allowing for easy installation around bends and corners. The included heat shrinkable tubes add an extra layer of protection and neatness. I’d be thrilled if Amazon or the company sent me more cable management products to try out! If you're looking for an effective way to protect and organize your cords, I highly recommend this wire loom!

My expectation for this product was not that high when i first ordered it, as soon as it arrived i installed it on my 50+ foot extension cord. Was a little bit tricky for me in the beginning because this was the first attempt to use this product and for the length im going for. When installing it make sure the cord is taped up and smooth so the wire can easily slide in, cut the ends with a hot knife or scissors (if u dont have a hot knife, use a stove or a lighter and it up high enough that when u cut it melts the plastic wire} ...I use what i called slide and stack wire but be carefull not to stack or bunch up the wire way too much, do a couple of stacks and slide it through with the rest all the way till ur able to stretch all the wire from the beginning, work ur way through and if it happens to snug up together, try pulling the wire back and if u want to tighten the wire on the cable, just twist wire and u'll notice the wire tightens up with the cord. Lastly measure twice cut ones rule. Give a little bit of an allowance till ur ready to finalize the cord and wire then u cut the wire and the rubber sleeves come in to play and basically secure the wire and cords end in place and gives u that professional look instead Durability? Lets just say i left it outside in the back of a busy alley to use and forgot to remove after, 2 days later i see the cord outside and expected the worse because the back alley is one of if not the worse back alley ive seen, the cement and asphalt all cracked up and very un even. So when i check the cord its like as good as the day i installed it, no rips nor tare on the wire and extension cords, The cord was run over multiple times by regular vehicles and work trucks plus 5 gabage truck that take out the trash for different establishments. Im impress on this wire loom to be honest, that im about to order more so i can wrap more cords inside the house this time/. Ill post pics soon

Its price is exceptional considering norm pay for a name brand thru a parts supplier 10 fold what this costs for 100'. Installs just as easy but definitely frays easier/ and far worse than the costlier ones. Put a video showing jist of how I put it on the wire. Can do a 20' run in just a few minutes. Wasnt as easy trying to do it in camera view tho. One hand milks a inch or 2 of it over the end of the wire and the other pulls it in while alternating which hand holds the wire inside, occasionally sweeping the gathered on down the wire. It gives it a nice look and will keep the wire from being chaffed thru good enough over time. Torn on if will purchase again due to how quickly it freys. The higher dollar stuff takes quite a bit of abuse before will start to frey so do norm get a run done and managed before it has a chance to. But this tends to unravel just from cutting it.

Works great.

Do you have cats? Do they especially like the phone charger cords? Well then this is for you! We use this to go around the white iphone cords that are not braided. I now only buy braided but this wrapped around the remaining non braided cords will do for now , or any new non braided cords we may acquire. Just make the end big enough to fit the plug in part of the iPhone cord thru it and then thread it through. You can then either use zip ties or black electrical tape at the ends.

I use this all the time for audio installs. Makes the wiring look very neat and organized. Protects well. Easy to cut to length.

This stuff is great! I bought it to recover the wires on my 3D printer. It's a it tricky to use, but if you follow the directs about heating your knife or scissors before cutting it, it seals up really nicely. Can be a bit tricky to feed ends with larger terminals through, but I found that if you "inchworm" it through, you can fit larger terminals through just fine. You also get a TON of this stuff for the price you pay. I don't think I'll ever run out

I've been using this type of electrical braiding for all kinds of applications (car, bike, house) - works wonders. This particular brand is of no exception in quality - the cost was effective in this particular purpose. Used it for a custom show bike with A1 results. The main deal here is whatever its used for is to order the right diameter - going to large has its drawbacks as such with ordering to slim a design and having to fight the fitment. Found it best to order 2 different diameters and go with it - the cost is well worth the time savings and the resulting appearance in the end. I normally do ends with min black zip ties as a lil tip. Do give apology for no pics here in which some illustrations would make for that much better review ... just no time - at this time - to do so.